Unitronics Structured Text for Packaging Automation: Complete Programming Guide

Learning to implement Structured Text for Packaging Automation using Unitronics's VisiLogic / UniLogic is a useful skill for PLC programmers working in Packaging. This guide walks through the fundamentals with clear explanations and an illustrative example that you can adapt to a simulator or test bench.

The example uses Unitronics terminology and references controller families such as Jazz 2 and Samba 7". Confirm the exact instructions, data types, firmware requirements, and licensing in the current vendor documentation before choosing hardware or deploying a project.

The Structured Text approach is particularly well-suited for Packaging Automation because complex calculations, data manipulation, advanced control algorithms, and when code reusability is important. This combination allows you to leverage powerful for complex logic while managing the typical challenges of Packaging Automation, including product changeover and high-speed synchronization.

Throughout this guide, you'll find step-by-step implementation guidance, an illustrative code example, and a verification checklist specific to Packaging. Whether you're programming your first Packaging Automation exercise or transitioning from another PLC platform, use the material as a starting point and validate it in your exact VisiLogic / UniLogic version and controller environment.

Unitronics VisiLogic / UniLogic for Packaging Automation

VisiLogic / UniLogic is a programming environment associated with Unitronics controller families such as Jazz 2, Samba 7", Vision V350. This guide uses Structured Text terminology from the supplied guide dataset, but controller capabilities and language support can change by model, firmware, software edition, and license.

Verify Before You Start:

The selected controller supports the required Structured Text constructs

The project version matches the installed VisiLogic / UniLogic release

Required communications, motion, safety, and simulation options are licensed

Firmware and device-description files are compatible with the project

The vendor manuals used for the design match the exact hardware revision

Application Planning:

For a Packaging Automation exercise, map the required inputs and outputs before writing logic. The example considers 5 sensor types, including Vision systems, Weight sensors, Barcode scanners, and 5 actuator types.

Control Equipment for Packaging Automation:

Form-fill-seal machines (horizontal and vertical)

Case erectors and sealers

Labeling systems (pressure sensitive, shrink sleeve)

Case packers (drop, wrap-around, robotic)

Controller-family references used in this guide include:

Jazz 2: Confirm CPU, I/O, memory, communications, and Structured Text support in the current selection guide

Samba 7": Confirm CPU, I/O, memory, communications, and Structured Text support in the current selection guide

Vision V350: Confirm CPU, I/O, memory, communications, and Structured Text support in the current selection guide

Vision V570: Confirm CPU, I/O, memory, communications, and Structured Text support in the current selection guide

Hardware Selection Checklist:

Count local and remote I/O, including planned expansion

Measure the required task and communications update rates

Identify memory, data-retention, diagnostics, and cybersecurity requirements

Treat safety functions as a separate, standards-led design activity

Confirm lifecycle status, regional availability, licensing, and support

Source and Validation Note:

This page does not represent a vendor certification or a hardware acceptance test. Use current Unitronics manuals, release notes, and safety documentation as the authority for product-specific behavior. Validate adapted logic in a simulator or isolated test setup before connecting it to equipment.

Investment Considerations:

For Packaging Automation projects, compare hardware, software licensing, training, engineering, test equipment, commissioning, spares, and ongoing support. Obtain current pricing and lifecycle information directly from the vendor or an authorized regional supplier.

Understanding Structured Text for Packaging Automation

Structured Text (ST) is a high-level, text-based programming language defined in IEC 61131-3. It resembles Pascal and provides powerful constructs for complex algorithms, calculations, and data manipulation.

Execution Model:

Code executes sequentially from top to bottom within each program unit. Variables maintain state between scan cycles unless explicitly reset.

Core Advantages for Packaging Automation:

Powerful for complex logic: Critical for Packaging Automation when handling intermediate to advanced control logic

Excellent code reusability: Critical for Packaging Automation when handling intermediate to advanced control logic

Compact code representation: Critical for Packaging Automation when handling intermediate to advanced control logic

Good for algorithms and calculations: Critical for Packaging Automation when handling intermediate to advanced control logic

Familiar to software developers: Critical for Packaging Automation when handling intermediate to advanced control logic

Why Structured Text Fits Packaging Automation:

Packaging Automation systems in Packaging typically involve:

Sensors: Product detection sensors for counting and positioning, Registration sensors for label and film alignment, Barcode/2D code readers for verification

Actuators: Servo drives for precise motion control, Pneumatic cylinders for pick-and-place, Vacuum generators and cups

Complexity: Intermediate to Advanced with challenges including Maintaining registration at high speeds

Programming Fundamentals in Structured Text:

Variables:
- declaration: VAR / VAR_INPUT / VAR_OUTPUT / VAR_IN_OUT / VAR_GLOBAL sections
- initialization: Variables can be initialized at declaration: Counter : INT := 0;
- constants: VAR CONSTANT section for read-only values

Operators:
- arithmetic: + - * / MOD (modulo)
- comparison: = <> < > <= >=
- logical: AND OR XOR NOT

ControlStructures:
- if: IF condition THEN statements; ELSIF condition THEN statements; ELSE statements; END_IF;
- case: CASE selector OF value1: statements; value2: statements; ELSE statements; END_CASE;
- for: FOR index := start TO end BY step DO statements; END_FOR;

Best Practices for Structured Text:

Use meaningful variable names with consistent naming conventions

Initialize all variables at declaration to prevent undefined behavior

Use enumerated types for state machines instead of magic numbers

Break complex expressions into intermediate variables for readability

Use functions for reusable calculations and function blocks for stateful operations

Common Mistakes to Avoid:

Using = instead of := for assignment (= is comparison)

Forgetting semicolons at end of statements

Integer division truncation - use REAL for decimal results

Infinite loops from incorrect WHILE/REPEAT conditions

Typical Applications:

1. PID control: Directly applicable to Packaging Automation
2. Recipe management: Related control patterns
3. Statistical calculations: Related control patterns
4. Data logging: Related control patterns

Understanding these fundamentals prepares you to implement effective Structured Text solutions for Packaging Automation using Unitronics VisiLogic / UniLogic.

Implementing Packaging Automation with Structured Text

Packaging automation systems use PLCs to coordinate primary, secondary, and tertiary packaging operations. These systems control filling, labeling, case packing, palletizing, and integration with production and warehouse systems.

This walkthrough demonstrates practical implementation using Unitronics VisiLogic / UniLogic and Structured Text programming.

System Requirements:

A typical Packaging Automation implementation includes:

Input Devices (Sensors):
1. Product detection sensors for counting and positioning: Critical for monitoring system state
2. Registration sensors for label and film alignment: Critical for monitoring system state
3. Barcode/2D code readers for verification: Critical for monitoring system state
4. Vision systems for quality inspection: Critical for monitoring system state
5. Reject confirmation sensors: Critical for monitoring system state

Output Devices (Actuators):
1. Servo drives for precise motion control: Primary control output
2. Pneumatic cylinders for pick-and-place: Supporting control function
3. Vacuum generators and cups: Supporting control function
4. Glue and tape applicators: Supporting control function
5. Film tensioners and seal bars: Supporting control function

Control Equipment:

Form-fill-seal machines (horizontal and vertical)

Case erectors and sealers

Labeling systems (pressure sensitive, shrink sleeve)

Case packers (drop, wrap-around, robotic)

Control Strategies for Packaging Automation:

1. Primary Control: Automated packaging systems using PLCs for product wrapping, boxing, labeling, and palletizing.
2. Safety Interlocks: Preventing Product changeover
3. Error Recovery: Handling High-speed synchronization

Implementation Steps:

Step 1: Define packaging specifications for all product variants

In VisiLogic / UniLogic, define packaging specifications for all product variants.

Step 2: Create motion profiles for each packaging format

In VisiLogic / UniLogic, create motion profiles for each packaging format.

Step 3: Implement registration control with encoder feedback

In VisiLogic / UniLogic, implement registration control with encoder feedback.

Step 4: Program pattern generation for case and pallet loading

In VisiLogic / UniLogic, program pattern generation for case and pallet loading.

Step 5: Add reject handling with confirmation logic

In VisiLogic / UniLogic, add reject handling with confirmation logic.

Step 6: Implement barcode/vision integration for verification

In VisiLogic / UniLogic, implement barcode/vision integration for verification.

Unitronics Function Design:

Function block design in Unitronics uses user-defined FBs in UniLogic (more limited in VisiLogic). Extensive vendor-provided helper FBs cover common tasks (PID, motion, communication, HMI utilities). OEM machine builders typically maintain private FB libraries for their common machine patterns, though code reuse is less mature than in mainstream PLC ecosystems.

Common Challenges and Solutions:

1. Maintaining registration at high speeds

Solution: Structured Text addresses this through Powerful for complex logic.

2. Handling product variability in automated systems

Solution: Structured Text addresses this through Excellent code reusability.

3. Quick changeover between package formats

Solution: Structured Text addresses this through Compact code representation.

4. Synchronizing multiple machines in a line

Solution: Structured Text addresses this through Good for algorithms and calculations.

Safety Considerations:

Guarding around rotating and reciprocating parts

Safety-rated position monitoring for setup access

Heat hazard protection for seal bars and shrink tunnels

Proper pinch point guarding

Robot safety zones and light curtains

Performance Metrics:

Task and I/O timing: Record minimum, average, and maximum values under a defined test load

Accuracy: Define an acceptable tolerance and compare it with calibrated reference measurements

Throughput: Count completed cycles over a fixed interval and record rejected or incomplete cycles

Fault response: Measure detection, safe-state, alarm, and recovery behavior for each test case

Resource use: Record memory, communications load, and diagnostic-buffer behavior

Unitronics Diagnostic Tools:

UniLogic (current) and VisiLogic (legacy) integrated debuggers with breakpoints,Built-in simulator covering PLC logic, HMI screens, alarms, recipes, and data tables,Web visualisation for UniStream — remote HMI viewing without additional software,SD card logging with PC-side export tools for offline trend analysis,Modbus RTU/TCP transaction logging built into the IDE,Controller status monitor — CPU load, scan time, memory usage,HMI event logger capturing operator actions for audit purposes,CAN bus diagnostic tools for CANopen-equipped models,Remote support tool — Unitronics' own screen-sharing for technical support,User community forum with active troubleshooting discussions

Use the monitoring and diagnostic functions available in your VisiLogic / UniLogic version, and record the software, firmware, hardware, workload, and test procedure with every result.

Unitronics Structured Text Example for Packaging Automation

Illustrative Structured Text example for Packaging Automation using Unitronics terminology. Adapt the syntax to your VisiLogic / UniLogic release, compile it, and verify it in an isolated test environment before use on equipment.

(* Unitronics VisiLogic / UniLogic - Packaging Automation Control *)
(* Structured Text Implementation for Packaging *)
(* Unitronics projects use IDE-managed tag names rather than raw memory a *)

PROGRAM PRG_PACKAGING_AUTOMATION_Control

VAR
    (* State Machine Variables *)
    eState : E_PACKAGING_AUTOMATION_States := IDLE;
    bEnable : BOOL := FALSE;
    bFaultActive : BOOL := FALSE;

    (* Timers *)
    tonDebounce : TON;
    tonProcessTimeout : TON;
    tonFeedbackCheck : TON;

    (* Counters *)
    ctuCycleCounter : CTU;

    (* Process Variables *)
    rVisionsystems : REAL := 0.0;
    rServomotors : REAL := 0.0;
    rSetpoint : REAL := 100.0; (* Illustrative value; replace with a reviewed requirement *)
END_VAR

VAR CONSTANT
    (* Packaging Process Parameters *)
    C_DEBOUNCE_TIME : TIME := T#500MS;
    C_PROCESS_TIMEOUT : TIME := T#30S; (* Illustrative value; verify for the process *)
    C_BATCH_SIZE : INT := 50; (* Illustrative value; replace with a reviewed requirement *)
END_VAR

(* Input Conditioning *)
tonDebounce(IN := bStartButton, PT := C_DEBOUNCE_TIME);
bEnable := tonDebounce.Q AND NOT bEmergencyStop AND bSafetyOK;

(* Main State Machine - Pattern: State machines are commonly implemented  *)
CASE eState OF
    IDLE:
        rServomotors := 0.0;
        ctuCycleCounter(RESET := TRUE);
        IF bEnable AND rVisionsystems > 0.0 THEN
            eState := STARTING;
        END_IF;

    STARTING:
        (* Ramp up output - Gradual start *)
        rServomotors := MIN(rServomotors + 5.0, rSetpoint);
        IF rServomotors >= rSetpoint THEN
            eState := RUNNING;
        END_IF;

    RUNNING:
        (* Packaging Automation active - Packaging automation systems use PLCs to coordinat *)
        tonProcessTimeout(IN := TRUE, PT := C_PROCESS_TIMEOUT);
        ctuCycleCounter(CU := bCyclePulse, PV := C_BATCH_SIZE);

        IF ctuCycleCounter.Q THEN
            eState := COMPLETE;
        ELSIF tonProcessTimeout.Q THEN
            bFaultActive := TRUE;
            eState := FAULT;
        END_IF;

    COMPLETE:
        rServomotors := 0.0;
        (* Log production data - Data logging uses UniLogic's Data Samplers — configured triggers (time-based or event-based) write structured records to Data Tables or SD card in CSV format. Exported files can be pushed via FTP or email. For cloud integration, UniCloud provides managed data ingestion. Simpler VisiLogic projects use HMI-triggered SD writes via custom ladder code. *)
        eState := IDLE;

    FAULT:
        rServomotors := 0.0;
        (* Alarm handling uses UniLogic's built-in Alarm Manager — configure alarm conditions in tables with severity, message text, and logging behaviour, and the engine handles detection, acknowledgement, history, and HMI display without custom code. VisiLogic uses a simpler alarm approach via HMI event handlers. *)
        IF bFaultReset AND NOT bEmergencyStop THEN
            bFaultActive := FALSE;
            eState := IDLE;
        END_IF;
END_CASE;

(* Safety Override - Always executes *)
IF bEmergencyStop OR NOT bSafetyOK THEN
    rServomotors := 0.0;
    eState := FAULT;
    bFaultActive := TRUE;
END_IF;

END_PROGRAM

Code Explanation:

1.Enumerated state machine (State machines are commonly implemented in ladder with step-counter registers or in ST using CASE structures with named state constants. UniLogic's HMI graphical bindings make state-to-screen visualisation straightforward — a single state variable drives both logic and operator screen transitions. SFC is not a primary language on Unitronics; state logic is typically CASE or ladder.) for clear Packaging Automation sequence control
2.Constants use clearly marked illustrative values that must be replaced with reviewed project requirements
3.Input conditioning with debounce timer prevents false triggers in industrial environment
4.STARTING state implements soft-start ramp - prevents mechanical shock
5.Process timeout detection flags a possible stuck condition for investigation
6.The final override illustrates a software permissive only; it is not a safety-rated function and must not replace a validated safety system

Best Practices

✓Follow Unitronics naming conventions: Unitronics projects use IDE-managed tag names rather than raw memory addressing.
✓Unitronics function design: Function block design in Unitronics uses user-defined FBs in UniLogic (more limi
✓Data organization: Unitronics uses its own tag database concept rather than IEC-standard data block
✓Structured Text: Use meaningful variable names with consistent naming conventions
✓Structured Text: Initialize all variables at declaration to prevent undefined behavior
✓Structured Text: Use enumerated types for state machines instead of magic numbers
✓Packaging Automation: Use electronic gearing for mechanical simplicity
✓Packaging Automation: Implement automatic film/label splice detection
✓Packaging Automation: Add statistical monitoring of registration error
✓Debug with VisiLogic / UniLogic: Use the built-in simulator to reproduce issues before hardware visit
✓Safety: Guarding around rotating and reciprocating parts
✓Use a compatible simulator or isolated test rig to test Packaging Automation logic before deployment

Common Pitfalls to Avoid

⚠Structured Text: Using = instead of := for assignment (= is comparison)
⚠Structured Text: Forgetting semicolons at end of statements
⚠Structured Text: Integer division truncation - use REAL for decimal results
⚠Unitronics common error: VisiLogic-to-UniLogic migration issues — not all projects convert cleanly
⚠Packaging Automation: Maintaining registration at high speeds
⚠Packaging Automation: Handling product variability in automated systems
⚠Neglecting to validate Product detection sensors for counting and positioning leads to control errors
⚠Insufficient comments make Structured Text programs unmaintainable over time

Related Certifications

🏆Unitronics Certified Integrator

🏆UniLogic Developer Training

🏆Advanced Unitronics Programming Certification

Applying Structured Text to Packaging Automation using Unitronics VisiLogic / UniLogic requires understanding the platform, the process, and the project's acceptance criteria. This guide has covered implementation structure, an illustrative code example, verification practices, and common pitfalls for a intermediate to advanced Packaging Automation exercise.

Use the practices outlined here to create a design that can be reviewed and tested. Define performance targets in the project requirements and confirm them with repeatable measurements.

Next Steps:

1. Check Sources: Read the current VisiLogic / UniLogic help, controller manual, release notes, and relevant standards
2. Practice Safely: Adapt the example in a simulator or isolated training setup
3. Review: Have the I/O map, state behavior, faults, and recovery steps reviewed
4. Test: Record normal, boundary, fault, restart, and communications test results

Structured Text Foundation:

Structured Text (ST) is a high-level, text-based programming language defined in IEC 61131-3. It resembles Pascal and provides powerful constructs for...

Project duration depends on scope, reviews, hardware availability, software and firmware versions, testing, commissioning, and site constraints. Remember: Use electronic gearing for mechanical simplicity

For further learning, explore related topics including Recipe management, Pharmaceutical blister packing, and Unitronics platform-specific features for Packaging Automation optimization.