Fatek Sequential Function Charts (SFC) for Pump Control: Complete Programming Guide

Implementing Sequential Function Charts (SFC) for Pump Control using Fatek WinProladder / FATEK Programming Software requires translating a control narrative into code, tests, and commissioning checks. This hands-on guide focuses on practical implementation steps, an illustrative code example, and decisions that should be recorded during design review.

The guide uses WinProladder / FATEK Programming Software terminology and Sequential Function Charts (SFC) because batch processes, step-by-step operations, state machines, and complex sequential control. Confirm language support for the selected controller and software release, then map the example's 5 sensor inputs and 5 actuator outputs to the project's reviewed I/O list.

Real Pump Control projects in Water & Wastewater face practical challenges including pressure regulation, pump sequencing, and integration with existing systems. Success requires balancing perfect for sequential processes against limited to sequential operations, while meeting 2-4 weeks project timelines typical for Pump Control implementations.

This guide provides step-by-step implementation guidance, an illustrative example, practical design patterns, and troubleshooting scenarios. Compile and test the adapted logic in an isolated environment, verify fail-safe behavior with the responsible controls and safety reviewers, and complete site acceptance checks before production use.

Fatek WinProladder / FATEK Programming Software for Pump Control

WinProladder / FATEK Programming Software is a programming environment associated with Fatek controller families such as FBs-MA, FBs-MC, FBs-MN. This guide uses Sequential Function Charts (SFC) terminology from the supplied guide dataset, but controller capabilities and language support can change by model, firmware, software edition, and license.

Verify Before You Start:

The selected controller supports the required Sequential Function Charts (SFC) constructs

The project version matches the installed WinProladder / FATEK Programming Software release

Required communications, motion, safety, and simulation options are licensed

Firmware and device-description files are compatible with the project

The vendor manuals used for the design match the exact hardware revision

Application Planning:

For a Pump Control exercise, map the required inputs and outputs before writing logic. The example considers 5 sensor types, including Pressure transmitters, Flow meters, Level sensors, and 5 actuator types.

Control Equipment for Pump Control:

Centrifugal pumps for high flow applications

Positive displacement pumps for metering

Submersible pumps for wet well applications

Booster pump systems for pressure maintenance

Controller-family references used in this guide include:

FBs-MA: Confirm CPU, I/O, memory, communications, and Sequential Function Charts (SFC) support in the current selection guide

FBs-MC: Confirm CPU, I/O, memory, communications, and Sequential Function Charts (SFC) support in the current selection guide

FBs-MN: Confirm CPU, I/O, memory, communications, and Sequential Function Charts (SFC) support in the current selection guide

FBs-CB (compact): Confirm CPU, I/O, memory, communications, and Sequential Function Charts (SFC) support in the current selection guide

Hardware Selection Checklist:

Count local and remote I/O, including planned expansion

Measure the required task and communications update rates

Identify memory, data-retention, diagnostics, and cybersecurity requirements

Treat safety functions as a separate, standards-led design activity

Confirm lifecycle status, regional availability, licensing, and support

Source and Validation Note:

This page does not represent a vendor certification or a hardware acceptance test. Use current Fatek manuals, release notes, and safety documentation as the authority for product-specific behavior. Validate adapted logic in a simulator or isolated test setup before connecting it to equipment.

Investment Considerations:

For Pump Control projects, compare hardware, software licensing, training, engineering, test equipment, commissioning, spares, and ongoing support. Obtain current pricing and lifecycle information directly from the vendor or an authorized regional supplier.

Understanding Sequential Function Charts (SFC) for Pump Control

Sequential Function Chart (SFC) is a graphical language for programming sequential processes. It models systems as a series of steps connected by transitions, ideal for batch processes and machine sequences.

Execution Model:

Only active steps execute their actions. Transitions define conditions for moving between steps. Multiple steps can be active simultaneously in parallel branches.

Core Advantages for Pump Control:

Perfect for sequential processes: Critical for Pump Control when handling intermediate control logic

Clear visualization of process flow: Critical for Pump Control when handling intermediate control logic

Easy to understand process steps: Critical for Pump Control when handling intermediate control logic

Good for batch operations: Critical for Pump Control when handling intermediate control logic

Simplifies complex sequences: Critical for Pump Control when handling intermediate control logic

Why Sequential Function Charts (SFC) Fits Pump Control:

Pump Control systems in Water & Wastewater typically involve:

Sensors: Pressure transmitters for discharge and suction pressure, Flow meters (magnetic, ultrasonic, or vortex), Level transmitters for tank or wet well level

Actuators: Variable frequency drives (VFDs) for speed control, Motor starters (DOL or soft start), Control valves for flow regulation

Complexity: Intermediate with challenges including Preventing cavitation at low suction pressure

Control Strategies for Pump Control:

constant: Maintain fixed speed or output

pressure: PID control to maintain discharge pressure setpoint

flow: PID control to maintain flow rate setpoint

Programming Fundamentals in Sequential Function Charts (SFC):

Steps:
- initialStep: Double-bordered box - starting point of sequence, active on program start
- normalStep: Single-bordered box - becomes active when preceding transition fires
- actions: Associated code that executes while step is active

Transitions:
- condition: Boolean expression that must be TRUE to advance
- firing: Transition fires when preceding step is active AND condition is TRUE
- priority: In selective branches, transitions are evaluated in defined order

ActionQualifiers:
- N: Non-stored - executes while step is active
- S: Set - sets output TRUE on step entry, remains TRUE
- R: Reset - sets output FALSE on step entry

Best Practices for Sequential Function Charts (SFC):

Start with a clear process flow diagram before implementing SFC

Use descriptive step names indicating what happens (e.g., Filling, Heating)

Keep transition conditions simple - complex logic goes in action code

Implement timeout transitions to prevent stuck sequences

Always provide a path back to initial step for reset/restart

Common Mistakes to Avoid:

Forgetting to include stop/abort transitions for emergency handling

Creating deadlocks where no transition can fire

Not handling the case where transition conditions never become TRUE

Using S (Set) actions without corresponding R (Reset) actions

Typical Applications:

1. Bottle filling: Directly applicable to Pump Control
2. Assembly sequences: Related control patterns
3. Material handling: Related control patterns
4. Batch mixing: Related control patterns

Understanding these fundamentals prepares you to implement effective Sequential Function Charts (SFC) solutions for Pump Control using Fatek WinProladder / FATEK Programming Software.

Implementing Pump Control with Sequential Function Charts (SFC)

Pump control systems use PLCs to regulate liquid flow in industrial processes, water treatment, and building services. These systems manage pump operation, protect equipment, optimize energy use, and maintain process parameters.

This walkthrough demonstrates practical implementation using Fatek WinProladder / FATEK Programming Software and Sequential Function Charts (SFC) programming.

System Requirements:

A typical Pump Control implementation includes:

Input Devices (Sensors):
1. Pressure transmitters for discharge and suction pressure: Critical for monitoring system state
2. Flow meters (magnetic, ultrasonic, or vortex): Critical for monitoring system state
3. Level transmitters for tank or wet well level: Critical for monitoring system state
4. Temperature sensors for bearing and motor monitoring: Critical for monitoring system state
5. Vibration sensors for predictive maintenance: Critical for monitoring system state

Output Devices (Actuators):
1. Variable frequency drives (VFDs) for speed control: Primary control output
2. Motor starters (DOL or soft start): Supporting control function
3. Control valves for flow regulation: Supporting control function
4. Isolation valves (actuated for remote operation): Supporting control function
5. Check valves to prevent backflow: Supporting control function

Control Equipment:

Centrifugal pumps for high flow applications

Positive displacement pumps for metering

Submersible pumps for wet well applications

Booster pump systems for pressure maintenance

Control Strategies for Pump Control:

constant: Maintain fixed speed or output

pressure: PID control to maintain discharge pressure setpoint

flow: PID control to maintain flow rate setpoint

level: Control tank/wet well level within band

Implementation Steps:

Step 1: Characterize pump curve and system curve

In WinProladder / FATEK Programming Software, characterize pump curve and system curve.

Step 2: Size VFD for application (constant torque vs. variable torque)

In WinProladder / FATEK Programming Software, size vfd for application (constant torque vs. variable torque).

Step 3: Implement primary control loop (pressure, flow, or level)

In WinProladder / FATEK Programming Software, implement primary control loop (pressure, flow, or level).

Step 4: Add pump protection logic (minimum flow, temperature, seal)

In WinProladder / FATEK Programming Software, add pump protection logic (minimum flow, temperature, seal).

Step 5: Program lead/lag sequencing with alternation

In WinProladder / FATEK Programming Software, program lead/lag sequencing with alternation.

Step 6: Implement soft start/stop ramps for smooth operation

In WinProladder / FATEK Programming Software, implement soft start/stop ramps for smooth operation.

Fatek Function Design:

P-label subroutines for reuse; some manufacturer-supplied FBs for motion and protocol-specific functions. Library reuse beyond manufacturer FBs is uncommon.

Common Challenges and Solutions:

1. Preventing cavitation at low suction pressure

Solution: Sequential Function Charts (SFC) addresses this through Perfect for sequential processes.

2. Managing minimum flow requirements

Solution: Sequential Function Charts (SFC) addresses this through Clear visualization of process flow.

3. Coordinating VFD speed with system pressure

Solution: Sequential Function Charts (SFC) addresses this through Easy to understand process steps.

4. Handling pump cycling with varying demand

Solution: Sequential Function Charts (SFC) addresses this through Good for batch operations.

Safety Considerations:

Dry run protection using flow or level monitoring

Overtemperature protection for motor and bearings

Overload protection through current monitoring

Vibration trips for mechanical failure detection

Emergency stop with proper system depressurization

Performance Metrics:

Task and I/O timing: Record minimum, average, and maximum values under a defined test load

Accuracy: Define an acceptable tolerance and compare it with calibrated reference measurements

Throughput: Count completed cycles over a fixed interval and record rejected or incomplete cycles

Fault response: Measure detection, safe-state, alarm, and recovery behavior for each test case

Resource use: Record memory, communications load, and diagnostic-buffer behavior

Fatek Diagnostic Tools:

WinProladder online monitor,Soft-element watch table,Built-in offline simulator,Modbus RTU / TCP communication analyzer,FvDesigner HMI runtime diagnostics,M8000-range system flags for hardware diagnostics,Distributor support engineers and loaner CPUs,Fatek user community forums (Taiwan-led)

Use the monitoring and diagnostic functions available in your WinProladder / FATEK Programming Software version, and record the software, firmware, hardware, workload, and test procedure with every result.

Fatek Sequential Function Charts (SFC) Example for Pump Control

Illustrative Sequential Function Charts (SFC) example for Pump Control using Fatek terminology. Adapt the syntax to your WinProladder / FATEK Programming Software release, compile it, and verify it in an isolated test environment before use on equipment.

// Fatek WinProladder / FATEK Programming Software - Pump Control Control
// Sequential Function Charts (SFC) Implementation for Water & Wastewater
// FX-style raw-address conventions dominate (X0, Y0, M100, D10

// ============================================
// Variable Declarations
// ============================================
VAR
    bEnable : BOOL := FALSE;
    bEmergencyStop : BOOL := FALSE;
    rPressuretransmitters : REAL;
    rCentrifugalpumps : REAL;
END_VAR

// ============================================
// Input Conditioning - Pressure transmitters for discharge and suction pressure
// ============================================
// Standard input processing
IF rPressuretransmitters > 0.0 THEN
    bEnable := TRUE;
END_IF;

// ============================================
// Safety Interlock - Dry run protection using flow or level monitoring
// ============================================
IF bEmergencyStop THEN
    rCentrifugalpumps := 0.0;
    bEnable := FALSE;
END_IF;

// ============================================
// Main Pump Control Control Logic
// ============================================
IF bEnable AND NOT bEmergencyStop THEN
    // Pump control systems use PLCs to regulate liquid flow in ind
    rCentrifugalpumps := rPressuretransmitters * 1.0; (* Illustrative scaling only *)

    // Process monitoring
    // Add specific control logic here
ELSE
    rCentrifugalpumps := 0.0;
END_IF;

Code Explanation:

1.Sequential Function Charts (SFC) structure organized for a Pump Control training example
2.Input conditioning handles Pressure transmitters for discharge and suction pressure signals
3.Safety interlock ensures Dry run protection using flow or level monitoring always takes priority
4.Main control implements Pump control systems use PLCs to regulat
5.Adapt the scan-cycle assumptions to the selected FBs-MA task configuration and verify them by measurement

Best Practices

✓Follow Fatek naming conventions: FX-style raw-address conventions dominate (X0, Y0, M100, D100, R0); symbolic nam
✓Fatek function design: P-label subroutines for reuse; some manufacturer-supplied FBs for motion and pro
✓Data organization: No structured DB; D / R register banks with engineer-documented range convention
✓Sequential Function Charts (SFC): Start with a clear process flow diagram before implementing SFC
✓Sequential Function Charts (SFC): Use descriptive step names indicating what happens (e.g., Filling, Heating)
✓Sequential Function Charts (SFC): Keep transition conditions simple - complex logic goes in action code
✓Pump Control: Use PID with derivative on PV for pressure control
✓Pump Control: Implement soft start ramps even with VFD (200-500ms)
✓Pump Control: Add flow proving before considering pump operational
✓Debug with WinProladder / FATEK Programming Software: Use the offline simulator before live download
✓Safety: Dry run protection using flow or level monitoring
✓Use a compatible simulator or isolated test rig to test Pump Control logic before deployment

Common Pitfalls to Avoid

⚠Sequential Function Charts (SFC): Forgetting to include stop/abort transitions for emergency handling
⚠Sequential Function Charts (SFC): Creating deadlocks where no transition can fire
⚠Sequential Function Charts (SFC): Not handling the case where transition conditions never become TRUE
⚠Fatek common error: Battery-low alarm on legacy FBs causing D-range loss
⚠Pump Control: Preventing cavitation at low suction pressure
⚠Pump Control: Managing minimum flow requirements
⚠Neglecting to validate Pressure transmitters for discharge and suction pressure leads to control errors
⚠Insufficient comments make Sequential Function Charts (SFC) programs unmaintainable over time

Related Certifications

🏆Fatek distributor-led engineer training

🏆WinProladder course completions

Applying Sequential Function Charts (SFC) to Pump Control using Fatek WinProladder / FATEK Programming Software requires understanding the platform, the process, and the project's acceptance criteria. This guide has covered implementation structure, an illustrative code example, verification practices, and common pitfalls for a intermediate Pump Control exercise.

Use the practices outlined here to create a design that can be reviewed and tested. Define performance targets in the project requirements and confirm them with repeatable measurements.

Next Steps:

1. Check Sources: Read the current WinProladder / FATEK Programming Software help, controller manual, release notes, and relevant standards
2. Practice Safely: Adapt the example in a simulator or isolated training setup
3. Review: Have the I/O map, state behavior, faults, and recovery steps reviewed
4. Test: Record normal, boundary, fault, restart, and communications test results

Sequential Function Charts (SFC) Foundation:

Sequential Function Chart (SFC) is a graphical language for programming sequential processes. It models systems as a series of steps connected by tran...

Project duration depends on scope, reviews, hardware availability, software and firmware versions, testing, commissioning, and site constraints. Remember: Use PID with derivative on PV for pressure control

For further learning, explore related topics including Assembly sequences, Wastewater treatment, and Fatek platform-specific features for Pump Control optimization.