B&R Industrial Automation Function Blocks for Pump Control: Complete Programming Guide

Learning to implement Function Blocks for Pump Control using B&R Industrial Automation's Automation Studio is a useful skill for PLC programmers working in Water & Wastewater. This guide walks through the fundamentals with clear explanations and an illustrative example that you can adapt to a simulator or test bench.

The example uses B&R Industrial Automation terminology and references controller families such as X20 CPU series and X90 Mobile. Confirm the exact instructions, data types, firmware requirements, and licensing in the current vendor documentation before choosing hardware or deploying a project.

The Function Blocks approach is particularly well-suited for Pump Control because process control, continuous operations, modular programming, and signal flow visualization. This combination allows you to leverage visual representation of signal flow while managing the typical challenges of Pump Control, including pressure regulation and pump sequencing.

Throughout this guide, you'll find step-by-step implementation guidance, an illustrative code example, and a verification checklist specific to Water & Wastewater. Whether you're programming your first Pump Control exercise or transitioning from another PLC platform, use the material as a starting point and validate it in your exact Automation Studio version and controller environment.

B&R Industrial Automation Automation Studio for Pump Control

Automation Studio is a programming environment associated with B&R Industrial Automation controller families such as X20 CPU series, X90 Mobile, APC2100. This guide uses Function Blocks terminology from the supplied guide dataset, but controller capabilities and language support can change by model, firmware, software edition, and license.

Verify Before You Start:

The selected controller supports the required Function Blocks constructs

The project version matches the installed Automation Studio release

Required communications, motion, safety, and simulation options are licensed

Firmware and device-description files are compatible with the project

The vendor manuals used for the design match the exact hardware revision

Application Planning:

For a Pump Control exercise, map the required inputs and outputs before writing logic. The example considers 5 sensor types, including Pressure transmitters, Flow meters, Level sensors, and 5 actuator types.

Control Equipment for Pump Control:

Centrifugal pumps for high flow applications

Positive displacement pumps for metering

Submersible pumps for wet well applications

Booster pump systems for pressure maintenance

Controller-family references used in this guide include:

X20 CPU series: Confirm CPU, I/O, memory, communications, and Function Blocks support in the current selection guide

X90 Mobile: Confirm CPU, I/O, memory, communications, and Function Blocks support in the current selection guide

APC2100: Confirm CPU, I/O, memory, communications, and Function Blocks support in the current selection guide

APC3100: Confirm CPU, I/O, memory, communications, and Function Blocks support in the current selection guide

Hardware Selection Checklist:

Count local and remote I/O, including planned expansion

Measure the required task and communications update rates

Identify memory, data-retention, diagnostics, and cybersecurity requirements

Treat safety functions as a separate, standards-led design activity

Confirm lifecycle status, regional availability, licensing, and support

Source and Validation Note:

This page does not represent a vendor certification or a hardware acceptance test. Use current B&R Industrial Automation manuals, release notes, and safety documentation as the authority for product-specific behavior. Validate adapted logic in a simulator or isolated test setup before connecting it to equipment.

Investment Considerations:

For Pump Control projects, compare hardware, software licensing, training, engineering, test equipment, commissioning, spares, and ongoing support. Obtain current pricing and lifecycle information directly from the vendor or an authorized regional supplier.

Understanding Function Blocks for Pump Control

Function Block Diagram (FBD) is a graphical programming language where functions and function blocks are represented as boxes connected by signal lines. Data flows from left to right through the network.

Execution Model:

Blocks execute based on data dependencies - a block executes only when all its inputs are available. Networks execute top to bottom when dependencies allow.

Core Advantages for Pump Control:

Visual representation of signal flow: Critical for Pump Control when handling intermediate control logic

Good for modular programming: Critical for Pump Control when handling intermediate control logic

Reusable components: Critical for Pump Control when handling intermediate control logic

Excellent for process control: Critical for Pump Control when handling intermediate control logic

Good for continuous operations: Critical for Pump Control when handling intermediate control logic

Why Function Blocks Fits Pump Control:

Pump Control systems in Water & Wastewater typically involve:

Sensors: Pressure transmitters for discharge and suction pressure, Flow meters (magnetic, ultrasonic, or vortex), Level transmitters for tank or wet well level

Actuators: Variable frequency drives (VFDs) for speed control, Motor starters (DOL or soft start), Control valves for flow regulation

Complexity: Intermediate with challenges including Preventing cavitation at low suction pressure

Control Strategies for Pump Control:

constant: Maintain fixed speed or output

pressure: PID control to maintain discharge pressure setpoint

flow: PID control to maintain flow rate setpoint

Programming Fundamentals in Function Blocks:

StandardBlocks:
- logic: AND, OR, XOR, NOT - Boolean logic operations
- comparison: EQ, NE, LT, GT, LE, GE - Compare values
- math: ADD, SUB, MUL, DIV, MOD - Arithmetic operations

TimersCounters:
- ton: Timer On-Delay - Output turns ON after preset time
- tof: Timer Off-Delay - Output turns OFF after preset time
- tp: Pulse Timer - Output pulses for preset time

Connections:
- wires: Connect output pins to input pins to pass data
- branches: One output can connect to multiple inputs
- feedback: Outputs can feed back to inputs for state machines

Best Practices for Function Blocks:

Arrange blocks for clear left-to-right data flow

Use consistent spacing and alignment for readability

Label all inputs and outputs with meaningful names

Create custom FBs for frequently repeated logic patterns

Minimize wire crossings by careful block placement

Common Mistakes to Avoid:

Creating feedback loops without proper initialization

Connecting incompatible data types

Not considering execution order dependencies

Overcrowding networks making them hard to read

Typical Applications:

1. HVAC control: Directly applicable to Pump Control
2. Temperature control: Related control patterns
3. Flow control: Related control patterns
4. Batch processing: Related control patterns

Understanding these fundamentals prepares you to implement effective Function Blocks solutions for Pump Control using B&R Industrial Automation Automation Studio.

Implementing Pump Control with Function Blocks

Pump control systems use PLCs to regulate liquid flow in industrial processes, water treatment, and building services. These systems manage pump operation, protect equipment, optimize energy use, and maintain process parameters.

This walkthrough demonstrates practical implementation using B&R Industrial Automation Automation Studio and Function Blocks programming.

System Requirements:

A typical Pump Control implementation includes:

Input Devices (Sensors):
1. Pressure transmitters for discharge and suction pressure: Critical for monitoring system state
2. Flow meters (magnetic, ultrasonic, or vortex): Critical for monitoring system state
3. Level transmitters for tank or wet well level: Critical for monitoring system state
4. Temperature sensors for bearing and motor monitoring: Critical for monitoring system state
5. Vibration sensors for predictive maintenance: Critical for monitoring system state

Output Devices (Actuators):
1. Variable frequency drives (VFDs) for speed control: Primary control output
2. Motor starters (DOL or soft start): Supporting control function
3. Control valves for flow regulation: Supporting control function
4. Isolation valves (actuated for remote operation): Supporting control function
5. Check valves to prevent backflow: Supporting control function

Control Equipment:

Centrifugal pumps for high flow applications

Positive displacement pumps for metering

Submersible pumps for wet well applications

Booster pump systems for pressure maintenance

Control Strategies for Pump Control:

constant: Maintain fixed speed or output

pressure: PID control to maintain discharge pressure setpoint

flow: PID control to maintain flow rate setpoint

level: Control tank/wet well level within band

Implementation Steps:

Step 1: Characterize pump curve and system curve

In Automation Studio, characterize pump curve and system curve.

Step 2: Size VFD for application (constant torque vs. variable torque)

In Automation Studio, size vfd for application (constant torque vs. variable torque).

Step 3: Implement primary control loop (pressure, flow, or level)

In Automation Studio, implement primary control loop (pressure, flow, or level).

Step 4: Add pump protection logic (minimum flow, temperature, seal)

In Automation Studio, add pump protection logic (minimum flow, temperature, seal).

Step 5: Program lead/lag sequencing with alternation

In Automation Studio, program lead/lag sequencing with alternation.

Step 6: Implement soft start/stop ramps for smooth operation

In Automation Studio, implement soft start/stop ramps for smooth operation.

B&R Industrial Automation Function Design:

B&R is famous for mapp Technology: a library of pre-engineered FBs covering motion (mapp Motion), robotics (mapp Robotics), HMI (mapp View), alarming (mapp Alarm), recipes (mapp Recipe), data logging (mapp Logger), auditing (mapp Audit), and cybersecurity (mapp Security). OEMs build atop mapp components rather than reimplementing. Private libraries of OEM-specific FBs are common, maintained in versioned Automation Studio libraries.

Common Challenges and Solutions:

1. Preventing cavitation at low suction pressure

Solution: Function Blocks addresses this through Visual representation of signal flow.

2. Managing minimum flow requirements

Solution: Function Blocks addresses this through Good for modular programming.

3. Coordinating VFD speed with system pressure

Solution: Function Blocks addresses this through Reusable components.

4. Handling pump cycling with varying demand

Solution: Function Blocks addresses this through Excellent for process control.

Safety Considerations:

Dry run protection using flow or level monitoring

Overtemperature protection for motor and bearings

Overload protection through current monitoring

Vibration trips for mechanical failure detection

Emergency stop with proper system depressurization

Performance Metrics:

Task and I/O timing: Record minimum, average, and maximum values under a defined test load

Accuracy: Define an acceptable tolerance and compare it with calibrated reference measurements

Throughput: Count completed cycles over a fixed interval and record rejected or incomplete cycles

Fault response: Measure detection, safe-state, alarm, and recovery behavior for each test case

Resource use: Record memory, communications load, and diagnostic-buffer behavior

B&R Industrial Automation Diagnostic Tools:

Automation Studio integrated debugger with breakpoints in every IEC language,System Diagnostics Manager — System-wide runtime health with historical retention,mapp View Diagnostic pages — ready-made diagnostic overlays for machine operators,ARsim integrated simulator — full offline machine testing without hardware,Motion commissioning via mapp Motion oscilloscope — waveform view during axis tuning,Task Class Monitor — per-task cycle time, jitter, and deadline violation tracking,System Designer — topology view of controllers, X2X modules, and powerlink devices,Logger module (mapp Logger) for structured event capture with severity classification,Online comparison between running controller and project — finds out-of-sync changes,mapp Audit — full audit trail of operator actions (GAMP 5 / 21 CFR Part 11 aligned)

Use the monitoring and diagnostic functions available in your Automation Studio version, and record the software, firmware, hardware, workload, and test procedure with every result.

B&R Industrial Automation Function Blocks Example for Pump Control

Illustrative Function Blocks example for Pump Control using B&R Industrial Automation terminology. Adapt the syntax to your Automation Studio release, compile it, and verify it in an isolated test environment before use on equipment.

(* B&R Industrial Automation Automation Studio - Pump Control Control *)
(* Reusable Function Blocks Implementation *)
(* B&R is famous for mapp Technology: a library of pre-engineer *)

FUNCTION_BLOCK FB_PUMP_CONTROL_Controller

VAR_INPUT
    bEnable : BOOL;                  (* Enable control *)
    bReset : BOOL;                   (* Fault reset *)
    rProcessValue : REAL;            (* Pressure transmitters for discharge and suction pressure *)
    rSetpoint : REAL := 100.0;  (* Illustrative value; replace with a reviewed requirement *)
    bEmergencyStop : BOOL;           (* Safety input *)
END_VAR

VAR_OUTPUT
    rControlOutput : REAL;           (* Variable frequency drives (VFDs) for speed control *)
    bRunning : BOOL;                 (* Process active *)
    bComplete : BOOL;                (* Cycle complete *)
    bFault : BOOL;                   (* Fault status *)
    nFaultCode : INT;                (* Diagnostic code *)
END_VAR

VAR
    (* Internal Function Blocks *)
    fbSafety : FB_SafetyMonitor;     (* Safety logic *)
    fbRamp : FB_RampGenerator;       (* Soft start/stop *)
    fbPID : FB_PIDController;        (* Process control *)
    fbDiag : FB_Diagnostics;         (* Alarm handling uses mapp Alarm — a pre-engineered component with severity classes, group acknowledgement, historical archival, and operator-visible banner generation on mapp View HMIs. Alarm definitions live in structured configuration files rather than in code, simplifying translation into multiple operator languages. Integration with mapp Audit captures every acknowledgement for regulated industries. *)

    (* Internal State *)
    eInternalState : E_ControlState;
    tonWatchdog : TON;
END_VAR

(* Safety Monitor - Dry run protection using flow or level monitoring *)
fbSafety(
    Enable := bEnable,
    EmergencyStop := bEmergencyStop,
    ProcessValue := rProcessValue,
    HighLimit := rSetpoint * 1.2,
    LowLimit := rSetpoint * 0.1
);

(* Main Control Logic *)
IF fbSafety.SafeToRun THEN
    (* Ramp Generator - Prevents startup surge *)
    fbRamp(
        Enable := bEnable,
        TargetValue := rSetpoint,
        RampRate := 20.0,  (* Illustrative value; tune and verify for the process *)
        CurrentValue => rSetpoint
    );

    (* PID Controller - Process regulation *)
    fbPID(
        Enable := fbRamp.InPosition,
        ProcessValue := rProcessValue,
        Setpoint := fbRamp.CurrentValue,
        Kp := 1.0,
        Ki := 0.1,
        Kd := 0.05,
        OutputMin := 0.0,
        OutputMax := 100.0
    );

    rControlOutput := fbPID.Output;
    bRunning := TRUE;
    bFault := FALSE;
    nFaultCode := 0;

ELSE
    (* Safe State - Overtemperature protection for motor and bearings *)
    rControlOutput := 0.0;
    bRunning := FALSE;
    bFault := NOT bEnable;  (* Only fault if not intentional stop *)
    nFaultCode := fbSafety.FaultCode;
END_IF;

(* Diagnostics - Data logging uses mapp Data and mapp Trend components — configured rather than coded. Structured logging of process variables, machine events, operator actions, and alarm history is handled by mapp components that write to local SD, networked SQL databases, or cloud endpoints. For regulated industries, mapp Audit provides GAMP 5 / 21 CFR Part 11 aligned electronic records. *)
fbDiag(
    ProcessRunning := bRunning,
    FaultActive := bFault,
    ProcessValue := rProcessValue,
    ControlOutput := rControlOutput
);

(* Watchdog - Detects frozen control *)
tonWatchdog(IN := bRunning AND NOT fbPID.OutputChanging, PT := T#10S);
IF tonWatchdog.Q THEN
    bFault := TRUE;
    nFaultCode := 99;  (* Watchdog fault *)
END_IF;

(* Reset Logic *)
IF bReset AND NOT bEmergencyStop THEN
    bFault := FALSE;
    nFaultCode := 0;
    fbDiag.ClearAlarms();
END_IF;

END_FUNCTION_BLOCK

Code Explanation:

1.Encapsulated function block follows B&R is famous for mapp Technology: a lib - reusable across Water & Wastewater projects
2.FB_SafetyMonitor illustrates status checks and high/low limits; it is not a certified safety function
3.FB_RampGenerator prevents startup issues common in Pump Control systems
4.FB_PIDController tuned for Water & Wastewater: Kp=1.0, Ki=0.1
5.Watchdog timer illustrates one way to flag an unchanged output for diagnosis
6.Diagnostic function block enables Data logging uses mapp Data and mapp Trend components — configured rather than coded. Structured logging of process variables, machine events, operator actions, and alarm history is handled by mapp components that write to local SD, networked SQL databases, or cloud endpoints. For regulated industries, mapp Audit provides GAMP 5 / 21 CFR Part 11 aligned electronic records. and Alarm handling uses mapp Alarm — a pre-engineered component with severity classes, group acknowledgement, historical archival, and operator-visible banner generation on mapp View HMIs. Alarm definitions live in structured configuration files rather than in code, simplifying translation into multiple operator languages. Integration with mapp Audit captures every acknowledgement for regulated industries.

Best Practices

✓Follow B&R Industrial Automation naming conventions: B&R projects follow strict Hungarian-style naming with prefixes (b for BOOL, n f
✓B&R Industrial Automation function design: B&R is famous for mapp Technology: a library of pre-engineered FBs covering moti
✓Data organization: B&R uses IEC 61131-3 global variable lists, PROGRAM VAR sections, and strongly-t
✓Function Blocks: Arrange blocks for clear left-to-right data flow
✓Function Blocks: Use consistent spacing and alignment for readability
✓Function Blocks: Label all inputs and outputs with meaningful names
✓Pump Control: Use PID with derivative on PV for pressure control
✓Pump Control: Implement soft start ramps even with VFD (200-500ms)
✓Pump Control: Add flow proving before considering pump operational
✓Debug with Automation Studio: Use Automation Studio breakpoints in ST — available across all IEC lan
✓Safety: Dry run protection using flow or level monitoring
✓Use a compatible simulator or isolated test rig to test Pump Control logic before deployment

Common Pitfalls to Avoid

⚠Function Blocks: Creating feedback loops without proper initialization
⚠Function Blocks: Connecting incompatible data types
⚠Function Blocks: Not considering execution order dependencies
⚠B&R Industrial Automation common error: Task class priority conflicts causing missed cycles in mid-priority application
⚠Pump Control: Preventing cavitation at low suction pressure
⚠Pump Control: Managing minimum flow requirements
⚠Neglecting to validate Pressure transmitters for discharge and suction pressure leads to control errors
⚠Insufficient comments make Function Blocks programs unmaintainable over time

Related Certifications

🏆B&R Certified Specialist

🏆B&R Certified Professional

🏆ABB University Automation Studio certifications

🏆Advanced B&R Industrial Automation Programming Certification

Applying Function Blocks to Pump Control using B&R Industrial Automation Automation Studio requires understanding the platform, the process, and the project's acceptance criteria. This guide has covered implementation structure, an illustrative code example, verification practices, and common pitfalls for a intermediate Pump Control exercise.

Use the practices outlined here to create a design that can be reviewed and tested. Define performance targets in the project requirements and confirm them with repeatable measurements.

Next Steps:

1. Check Sources: Read the current Automation Studio help, controller manual, release notes, and relevant standards
2. Practice Safely: Adapt the example in a simulator or isolated training setup
3. Review: Have the I/O map, state behavior, faults, and recovery steps reviewed
4. Test: Record normal, boundary, fault, restart, and communications test results

Function Blocks Foundation:

Function Block Diagram (FBD) is a graphical programming language where functions and function blocks are represented as boxes connected by signal line...

Project duration depends on scope, reviews, hardware availability, software and firmware versions, testing, commissioning, and site constraints. Remember: Use PID with derivative on PV for pressure control

For further learning, explore related topics including Temperature control, Wastewater treatment, and B&R Industrial Automation platform-specific features for Pump Control optimization.